概述Outline

该气源处理三联件包括空气减压阀、过滤器、油雾器、三大件。其中减压阀可对气源进行稳压，使气源处于恒定状态，可减小因气源气
压突变时对阀门或执行器等到硬件的损伤。过滤器用于对气源的清洁，可过滤压缩空气中的水分，避免水分随气体进入装置。油雾器对
机体运动部件进行润滑，可以对不方便加润滑油的部件进行润滑，大大延长机体的使用寿命。

The gas source processing parts, including air triple valve, filter, lubricator, the Big Three.Shielding=left>安装Installation
1.安装接头，连接气管前应辨认气源的进出口，本体上的箭头表示气源的流向。
2.接头的选择应与本体上的管螺纹相一致。接头安装时管螺纹上应缠绕适当的生料带，以确保其密封的可靠性。
3.本体的正面安装压力表，背面螺纹孔，用相应的堵头密封。
4.先将本体与专业连接板相连接。然后将专用连接板固定在自制的转接板上，再与执行机构相连接。
5.安装时应将毛刺、赃物去除干净，不要使其流入管道，以免堵塞气管。

1、install connector before connecting the trachea to identify the source of gas imports and exports, the arrowShielding=left>使用说明Instructions for use
1.本过滤器排水有压差排水与手动排水二种方式。手动排水时当水位达到滤芯下方水平之前必须排除。
2.压力调节时，在转动旋钮前请先拉起再旋转，压下旋转钮为定位。旋转钮向右为调高出口压力，向左旋转为调低出口压力。调节压力时
应逐步均匀地调至所需压力值，不应一步调节到位。
3.给油器的使用方法：给油器使用JIS K2213输机油(IS0Vg32或同级用油)。加油量请不要超过杯子八分清。数学0为油量*小，9为
油量*大。自9-0位置不能旋转，须顺时针旋转。

1、The filter pressure drainage and drainage are two ways to manually drain. Manual drainage when the water level below the level reached before the filter must be excluded.
2、Pressure regulator, in turn the knob and then pull up before the first rotation, rotate the knob depressed for the position. Rotate button to the right to increase outlet pressure, rotation to the left to reduce the outlet pressure. Adjust the pressure
Should be gradually raised to the required pressure evenly, not a step adjustment in place.
3、To the oil cooler to use: to oil cooler transmission oil with JIS K2213 (IS0Vg32 oil or equivalent). Do not exceed the amount of fuel to distinguish between the cup eight. 0 is the smallest oil mathematics, 9 to
Maximum oil. Since the 9-0 position can not be rotated to be clockwise.

型号 Model		AC1500	AC1500	AC2000	BC2500	BC3000	BC4000
工作介质 Working medium
接口管径 Interface diameter		G1/8	G1/8	G1/4	G1/4、G3/8	G3/8	G1/2
*大可调范围 The adjustable range		0.95Mpa
使用温度范围 Operating temperature range		5~60℃
建议润滑用油 Recommended lubricating oil		ISO VG 32
重量(kg) Weight (kg)		0.7	0.7	0.9	0.9	0.9	0.9
构成元件 Constitute the components	过滤器 Filter	AF1500	AF1500	AF2000	AF2500	AF3000	AF4000
	减压阀 Valve	AF1500	AR1500	AR2000	AR2500	AR3000	AR4000
	油雾器 Lubricator	AF1500	Al1500	A12000	A12500	A13000	A14000

ALS10系列阀位反馈装置是自控系统中检测阀门状态的一种现场仪表，用以将阀门的开启或关闭位置以开关量(触点)的信
号输出，被程控器接受或计算机寻访采样，确认后执行下一程序。该产品也可作为自控系统中重要阀门联锁保护及远程报警
指示之用。
工作原理
ALS10系列阀位反馈装置检测阀位转角位移，通过同轴连接件或反馈杆使传动轴产生选择，让凸轮触动微型开关，从而使开
关组建的触点闭合或断开，通过接线端子向外部传送开关量信号，并通过指示器就地显示。
技术要求
防护等级：IP65(本质安全型)IP67(外壳防护型)
触点容量：6A/24VDC(直流)10A/220VAC(交流)
环境温度：-15℃~+70℃
接线端口：2-G1/2″
旋转角度：0° -90° 角行程
位置指示：开一黄，关一红
外形尺寸：120×120×103mm
重量：约1.6kg

ALS10 series valve position feedback device is the automatic control system to detect the status of a field instrument valve to the valve open or closed position to switch (contact) letter
Number of output, the computer is programmed to accept or look for the sampling device, confirmed the next procedure. The product can also be important as self-control valve interlock system and remote alarm
Instructions for use.
Work
ALS10 series valve position feedback device to detect displacement of valve angle, coaxial connectors, or through the feedback lever shaft have to choose, let the cam touch micro switch, so that the open
Contact closure or shut off the formation, through the terminal to the external switch signal transmission, and display by local indicators.
Technical Requirements
Protection class: IP65 (intrinsically safe) IP67 (Enclosure Type)
Contact capacity: 6A/24VDC (DC) 10A/220VAC (AC)
Ambient temperature: -15 ℃ ~ +70 ℃
Wiring port :2-G1 / 2 "
Rotation angle: 0 ° -90 ° angle of travel
Position indication:Shielding=left>零件材料Part Material

名称 Name	数量 Quantity	材料 Material
位置指示器外壳 Position indicator housing	1	聚碳酸酯 Polycarbonate
位置指示器内壳 Position indicator within the shell	1	聚碳酸酯 Polycarbonate
壳体 Case	1	压铸铝合金 Aluminum die-casting
盖 Cover	1	压铸铝合金 Aluminum die-casting
轴 Axis	1	1Cc18Ni9Ti
微动开关 Micro Switch	2	组合件 Assembly
垫圈 Washer	2	HPb59-1
“O”型圈 "O"-ring	10	腈RCN橡胶 RCN nitrile rubber
凸轮 Cam	2	聚碳酸酯(开/关) Polycarbonate Shielding=center align=middle width=127> 弹簧 Spring	1	1Cc18Ni9Ti
上盖螺栓 Cover bolts	4	1Cc18Ni9Ti
接线板 Wiring board	8点	聚乙烯(PB) Polyethylene (PB)

安装及使用Installation and use
1.让阀门走到关的位置，调节红色凸轮，使“关”开关有信号输出。
2.让阀门走到开的位置，调节黄色凸轮，使“开”开关有信号输出。
3.让阀门来回走几次，确定限位开关信号通断可靠。
VLA1防爆型阀门范围装置
防爆标志：ExdⅡBT4(隔爆型)
防护登记：IP65

1. Let go off the valve position, adjusting the red cam, so that the "off" switch signal output.
2.to go to open the valve position, adjust the yellow cam, so that the Shielding=left>

var isView = 0;